T-shaped Groove Bottom PlateIt Is A Flat Reference Measuring Tool Used For Workpiece And Equipment Inspection, Marking, Assembly, Welding, Assembly, And Riveting. The Operation Of Marking The T-shaped Groove Bottom Plate Reference First Needs To Find Out Whether The Reference Of The Marking Workpiece Is Flat. You Can Directly Use A Height Vernier Ruler To Mark On The Marking Platform. If The Benchmark For Marking The Workpiece Is The Base Plane, The Base Plane Should Be Found First, And Then Starting From The Base Plane, A Height Vernier Ruler Should Be Used To Mark The Line. The Working Surface Of The T-shaped Groove Bottom Plate Shall Not Have Defects That Seriously Affect Its Appearance And Performance, Such As Sand Holes, Air Holes, Cracks, Slag Inclusions, Shrinkage, Scratches, Bumps, Rust Spots, Etc.
The Cast Iron Inspection Platform Is Suitable For Various Inspection And Measurement Work, Using Basic Planes And Rulers, Square Boxes, V-shaped Frames (iron), Bending Plates, Right Angle Rulers, Cylindrical Angle Rulers And Other Tools In Combination. The Cast Iron Inspection Platform Is Used For Machine Tools, Machinery, And Inspection Measurement To Check The Size, Accuracy, Flatness, Parallelism, Flatness, Perpendicularity, And Positional Deviation Of Parts And Make Lines. After Stability Treatment And Demagnetization, The Cast Iron Inspection Plate Enters The Machining Process, Which Is Divided Into Rough Planing And Fine Planing. Fine Planing Is A Process To Determine The Third Level Accuracy And Surface Roughness Of The Cast Iron Inspection Plate. Cast Iron Inspection Plates With A Second Level Or Higher Accuracy Need To Be Manually Scraped And Ground To Determine The Geometric Accuracy Of The Plate. Qualified Cast Iron Inspection Plates Should Avoid The Influence Of Heat Sources And Corrosion From Acid And Alkali. The T-shaped Groove Bottom Plate Should Be Placed At A Constant Temperature Of 20 ℃± 5 ℃.
The T-shaped Groove Bottom Plate Should Be Installed And Debugged By Specialized Personnel Before Use. How To Install And Debug It Correctly? The Specific Method Is As Follows:
1、 The T-shaped Groove Bottom Plate Should Be Wiped Clean And Should Not Be Used For A Long Time. Anti Rust Oil Should Be Applied To The Surface Of The T-shaped Groove Bottom Plate To Prevent Rusting.
2、 The Treatment Of T-shaped Groove Bottom Plate Should Be Careful And Extensive Operation Is Strictly Prohibited.
3、 The T-shaped Groove Bottom Plate Should Be Stored In A Dry And Ventilated Warehouse, And Should Not Be Placed In Cold And Humid Places, Not To Mention Water Droplets On The Surface Of The T-shaped Groove Bottom Plate.
4、 The T-shaped Groove Bottom Plate Cannot Be Stacked To Prevent Deformation Caused By Stacking Squeezing The T-shaped Groove Bottom Plate.
5、 Before Using The T-shaped Groove Bottom Plate, Specialized Personnel Are Required To Inspect And Debug The Plate Before Use. When Installing The Platform, Place A T-shaped Groove Bottom Plate Bracket At The Main Support Point.
6、 When Using A T-shaped Groove Bottom Plate, Mechanical Equipment Components Should Be Gently Placed To Prevent Strong Collisions Between The Mechanical Equipment Components And The T-shaped Groove Bottom Plate. If The Surface Of The Steel Plate Collides With Mechanical Parts, The Components Received From The Impact Depression Or Protrusion Should Be Repaired Before Continuing To Use.
7、 The Surface Of The T-shaped Groove Bottom Plate Should Be Kept Clean And Cleaned Promptly After Use To Avoid Residual Iron Filings, Sand Particles, Or Other Impurities On The Surface Of The T-shaped Groove Bottom Plate. These Iron Impurities Are Prone To React With The Cast Iron On The Surface Of The T-shaped Groove And T-shaped Groove Bottom Plate In Humid Air, Causing Corrosion On The Surface Of The T-shaped Groove And T-shaped Groove Bottom Plate. Even If Not In Humid Air, These Impurities Can Easily Scratch The Surface Of The T-shaped Groove Bottom Plate, Thereby Reducing The Accuracy Of The T-shaped Groove Bottom Plate. Therefore, They Need To Be Cleaned In A Timely Manner.
8、 When Using A T-shaped Groove, The T-shaped Groove Bottom Plate Should Be Used Uniformly In All Parts As Much As Possible To Avoid Excessive Use Caused By Local Wear.
9、 When Installing Mechanical And Equipment Components, Do Not Install Them On The T-shaped Groove Bottom Plate, And Do Not Use Hammers, Pliers, And Other Tools To Strike The Steel Plate.
